Aims: To provide a 30 minutes session where the BBR / HI system will carry the CoRe frequencies found in an evaluation, for 11 minutes, followed by a BBR / HI session only, for another 20 minutes.

Kiran: Yes right you stimulate the patient first with  Rife-frequencies modulated on Eigen-frequencies – this has a much deeper effect than Rife-Frequencies alone as the the Eigen-Frequencies carrier acts like a Trojan Horse that allows the Rife frequencies to bypass the persons energetic immune response.

Then afterwards in order to integrate this information it is of benefit to run Eigen-frequencies alone

To create a simple set up which can take advantage of the CoRe and BBR combination, connecting the head and the feet (top and ground) as well as the right and left side of body, as needed, while having the minimum manipulations of the client, cables, applicators and connectors.

 

Applicators used:

–          2 metallic foot plate using the 2 foot connectors, one in Body Signal, the other in Ref of the BiolaesEr.

–          2 hands rods connected to CH1 and Ch2 of the HI

–          Magnet using the negative pole on the body, connected to the HI magnetic port

–          Goggle connected to the Light Therapy port of the HI

 

Connections:

–          BioLaesEr connected to the HI via the HI Ref port of the BioLaesEr to the Ref of the HI in the front

–          In the back Signal out from the BioLaesEr connected to the Source In of the HI

–          Audio out (headphone) from the computer connected to Source In of the BioLaesEr

BioLaesEr Set Up

Example 1:

First 11 minutes of CoRe session broadcasted by the HI and mixed 50 / 50 with the Client Eigen Frequencies.

Sensitivity: Low = Therapy Mode

Inversion: Off = Homeopathic mode

Amplification: 10

Both Sensitivity and Amplification setting and fine tuning on knob 1 will determine what intensity is given out on ch 1 and ch2 that are displayed on the Health Integrator LED bars

 

BioLaesEr Set Up:

• First Knob on 0
• Second Knob on 50 / 50

Computer Set Up:

• The Report of the Evaluation is open and Single Frequency communication is set up for 11 minutes.
• The sound volume of the computer is set up on 20% and the Switch Energetic Carrier ON button is clicked.
• With the client hooked, we gradually bring the computer sound volume up to suite the client sensitivity.
• I try to reach 100% of the sound volume.

 You do not need to reach anything – the volume control just acts as a pre-amplifier and the intensity you apply is compounded with the amplification setting on the Bio-LaesEr and displayed at the Health Integrator LED bars – what voltage you need is client specific

 

This Set Up works on the Left and Right side of the body

Kiran: you are sensing with the Bio-LaesEr the electric differences between the right and the left side of the body by having one foot on Biosignal and the other on REF – this is good when you have a client with strong Yin Yang DLE issues like problems with his/ her male female identity 

 

 

This one will connect the head and the feet, the top and the bottom

Kiran :However you have to understand that C1 of the HI output is always the unmixed eigen-signal whereas ch2 is the eigen-frequency modulated by the Rife or other frequencies if these are added via the Source-In of the Bio-LaesEr and the middle Knob is not on 100%  feedback but any other ratio 

 

 

Once the 11 minutes Single Communication is finished, the goggles will shut off (at least the right eye).

Kiran : not always because the right is connected to ch2 which contains the eigen-frequencies modulated by Rife frequencies and if these stop the intensity might fall below the level that make the LED light up 

 

The second button of the BioLaesEr is then turned more on the Right, so the client Eigen Frequency received by the BioLaesEr footplate can feed the energy to power up the LED goggles (the right eye).

 correct – then you just increase the eigen-frequency part on the right eye LED goggles 

The client then rest in this position for 20 minutes.

 yes VERY IMPORTANT after any stimulation with external frequencies, be it electric or audio, massage or light have at least the same amount of time with Eigen-frequencies alone that creates a phase of quietness and centeredness

Additional music / NLP / affirmations could also be broadcasted to the client via an mp3 player connected to Source In of the BioLaesEr. In this case, the second button of the BioLaesEr could be set up at 50 / 50 while the volume of the mp3 player will be use to power the goggles. A twin audio Out port would be needed to connect a headphone set or speakers in order to hear the music / NLP / Affirmation broadcasted.

 

NOTES:

With this set up and the BioLaesEr Amplification switched on 1, although the first LED column can be fine tuned just right so the orange LED doesn’t show or barely show, I don’t have enough power to light up the goggles and magnet.

When I switch the BioLaesEr Amplification on 10, the LED from the first button / column turn bright orange (not recommended), even if the first knob is set on 0.

So I don’t feel good to use this setup with the orange LED on full power because you explained that was not right (can’t remember the details of your explanation but it made lot of sense then. Any suggestion would be appreciated.

 Dont worry about this the Orange top LED just indicates that you gut of some peaks from the signal – this does not hurt the patient but possibly just limits the fidelity of the signal but may often be necessary to have the desired higher output on LED or other applicators

 

Example 2, ALLOPATHIC MODE:

 

First 11 minutes of CoRe session broadcasted by the HI and mixed 50 / 50 with the Client Eigen Frequencies.

 

Sensitivity: Low = Therapy Mode

Inversion: On= Allopathic Mode

Amplification: 10

 

BioLaesEr Set Up:

 

• First Knob on 0
• Second Knob on 70% Feedback

Computer Set Up:

• The Report of the Evaluation is open and Single Frequency communication is set up for 11 minutes.
• The sound volume of the computer is set up on 20% and the Switch Energetic Carrier ON button is clicked.
• With the client hooked, we gradually bring the computer sound volume up to suite the client sensitivity.
• At 30% of the sound volume control, the client reacted

 

NOTES: 

Using this set up on ALLOPATHIC MODE = Inversion Mode and the BioLaesEr Amplification switched on 1, the client receive more electric shocks than when the BioLaesEr Amplification switch is on 10 ??? I have not tried the 100 with the Allopathic mode.

Kiran :In the Allopathic Mode the client does not get any higher voltage intensities but the signal is just an inverted copy of this Eigen-frequencies and this acts like a mirror effect that especially in those clients who deny to see their own needs and energy pattern may lead to a stronger sometimes shocking reaction – but this is by no means a general effect  and may be very curative for those 50% of client who more tend to set their own needs second to those requested by their environment