Manual / Part 3 – Setting Channel 1 & 2

4


The BEaMEr has 3 different sources for the output signal. 

 

1. Audio signal that is fed to the BEaMEr via the Audio-download cable

2. Audio signal that has been recorded – similar to a flash MP3 player

3. The internal frequency generator 

4. The Heartbeat sensor

 

Channel 1

 

1. If the HDMI-Audio transfer cable is connected to the headphone-output  of a PC or an MP3 player and sound is played this signal will be automatically used instead of the internally stored frequencies and

the BEaMEr transforms this signal into a signal of Light, Electricity and Magnetism (Note : while this is happening and the yellow 5th (Energy)-LED is blinking this indicates that the volume of the mp3 player is set too high, reduce it just enough that the LED is off most of the time. (also CHANNEL1 should  be set to R1 and CHANNEL2 should  be set to R2)

This mode not only allows to use signals that are created by the CoRe System or any other frequency generator but likewise music, nature sounds  or recorded spoken words to be used for Therapy with the BEaMEr, which is a completely new dimension of energy medicine.

 

2. R1, R2 — plays the Recoding from the internal flash memory of channel 1 and 2 respectively 

If  Channel2 is set to R2 the therapy is stereo with different signals on both channels to create an additional polar stimulus (whereas if it set to Ch1 on both channels the signal set for Channel 1 is played)

3. GEN1, Gen2 — outputs the signal of the internal Frequency Generator

The BEaMEr has the amazing ability to generate up to 25o 000 Hz. These frequencies are divided in 10 different ranges, starting at 0.1 Hz :

To select one or several frequency ranges for Channel 1 or Channel 2 by following these 3 easy steps :

1 — select Gen1 Action for Ch1 as always by holding the upper button for 2 sec when in the CHANNEL 1 function (or for Ch2 accordingly)

2 — the current set of selected ranges is shown – (in this example below only range 4, which is 7 to 40 Hz is not selected)

3 — to set also this range one pushes the lower button until this LED is blinking and then pushes the upper button once 

In this mode the lower button just changes the position of all the LED and when pushing the upper button in any blinking position shortly, it unselects a previously selected range or selects a range that was before switched off

Frequency ranges : (every range is scanned for 1 min with the increments listed below, the lowest yellow LED indicates range 1 and the uppermost green LED the range 10 accordingly(
1      o.1 Hz  symetric cycles of 10 sec  1.5 kHz bursts (lowest yellow LED)
2      0.5 Hz  symetric cycles of 5 sec  1.5 kHz bursts
3      1 Hz  symetric cycles of 1 sec  1.5 kHz bursts
4     5 – 9 Hz  step o.1 Hz — the Schuhmann window
5    9 -150 Hz step 1Hz
6    150-750 step 1Hz 
7    750-1500 step 10Hz
8    1500-2500 step 10Hz 
9    2.5-25kHz step 100Hz 
10  25-250 kHz step 100Hz (uppermost green LED)

 

4.  HB –Signal of a Heartbeat sensor

With the the Electrocardiogram cable and the Sensor attached the Heartbeat can be transformed in realtime on Channel 1 into TENS, Light and Magnetism (as well as Scalar energy if the INV mose is set)

If addtionally Channel2 is set to CH1 the Heartbeat signal is running on both channels

 

5. AUX — reserved for switching  another applicator ON that is currently in development

 

6. PROG — is programing the BEaMEr with a set of parameters that is Indication (disease) specific 

using the QuantumDoctor program the Program number between 1-10 is provided for a selected Indication

1 — set PROG in the usual way

2 — the BEaMEr switches to allow the Prog number to be selected  – here the bottom button switches the blinking LED   and when reaching the desired Program a single push of the upper button sets the Program. (in this example Prog 3 is selected)

 

Channel 2

 

7.  R2 and Gen2 — function as in channel1 – see above

8. Ch1 — if Channel2 is set to Ch1 on channel2 the signal that is set for ch1 (e.g. R1, Gen1 or HB) is output also on Ch2 which means you have a Mono signal

9. Rev — in this function the Frequency ranges selected with GEN1 are played on this channel 2 in reverse order,

which means starting with the highest frequencies first. This creates an additional DLE effect just as the W1 and W10 functions for Amplitude modulation but in this case to promote healing by confronting the energy system of the client with polarities of frequencies – the use and effectiveness of this mode needs further research. (please experiment and report results !)

10. INV — plays the inverted the channel1 signal here

one method  to create Scala energy is to run 2 signals on a bifilar coil as installed in the BEaMEr, with a phase difference ot 180 degree which is done in this mode – the use and effectiveness of this mode needs further research. (please experiment and report results !)

 

 

 

 

Share.

About Author

4 Comments

  1. I work with the system S2 advanced CoRe System, I can directly record up to 10 different programs without the Quantum Doctor? Can I use Beamer to a family of 4 people and give each one its own program? How do I record a program in place 1.2 , 3 etc?
    thank you very much
    Stefano

    • Dear Stefano

      you can simply select one, several or all of 10 Frequency generator ranges per channel which gives you 10 Exp 10 combinations – which is an astronomical
      number and can be done within about 10 seconds

      Kiran

      • Dear Kiran,
        in reference to “6. PROG — is programing the BEaMEr with a set of parameters that is Indication (disease) specific
        using the QuantumDoctor program the Program number between 1-10 is provided for a selected Indication”‘ll ask: is it possible to program the beamer (programs 1 to 10) without the QuantumDoctor but with an evaluation carried out with C2 CoRe System? If it is possible how do you proceed?
        many thanks
        Stefano

Reply To Kiran Schmidt Cancel Reply



Dear Friends and Customers

I am sorry to inform you that I have broken-up business relations with Andrea Gadducci and his company Biot Srl.

After years of paying commissions for software and hardware they have now informed me that they consider both to be their property - which according to their lawyer Guliano Lemme also includes the Inventory of Inergetix products that I had stored at their Rome office and for which I paid rent since it was moved there in June 2018 from Germany.

Until we have decided this matter in court i have to warn you not to buy from Andrea - as these goods might be later declared as stolen and you might loose the money you spend.

However I can offer you to buy directly from me and get a 10% discount to what Andrea quotes you. Please contact me at [email protected]

Thank you for your support in this DLE

Kiran Schmidt