Manual / Part 1 – selecting CoRe – Recording frequencies – Selecting Therapy Energies

2

This post is also available in: Chinese (Traditional) Croatian French German Greek Hungarian Indonesian Italian Portuguese (Brazil) Romanian Spanish

The BEaMEr has a stunning array of functions never befor found in any device so small that you could wear it 24/7, one would imagine this would require a complex user interface 

However we have built in 2 features that will make it very easy :

A) First if the PROG function is seleted only one of 10 built-in programs needs to be selected. The program number is determined client specifically, for a small fee via the online Virtual Doctor. (this software will be discussed in the next post9

B) Also the same can be done off-line if you own the heartpath module which can then base the CoRe algorythm on the recording of the clients heartbeat pattern to find the Frequency ranges and combinations which best suit the clients condition.

Equally unique  is the fact that frequencies can be applied not only as electric impulses TENS but also as magnetic, light, Infrared and even Scalar energy individually or synchoniously.

 

1. ON/OFF — Switch

There a only two buttons the lower one next to the yellow LED selects the FUNCTION –  the upper button sets a particular ACTION by holding it 2 seconds at one of the green LED positions

To switch ON hold both buttons  2 sec at the same time

To switch OFF hold both buttons  2 sec at the same time

 

2. TENS, IR, VIS, MAG — Selecting which Energy forms to be used

The BEaMEr has only two buttons, the one next to the yellow LED selects the FUNCTION, the one next to the green LED selects the Sub-Function or as we call them, the ACTIONs. Pressing the “yellow LED” button cycles through the FUNCTIONs, the “green LED” button cycles through the available Actions for this Function, holding this button longer  than 2 seconds will toggle the respective Subfunction ON or OFF .

As always in selecting a certain ACTION: – move the the yellow LED to the corresponding FUNCTION – in this case ENERGY and then select or unselect a specific Energy via pushing the Sub-function button longer than 2 sec next to the specific Energy LED

in this the example switching IR off and  MAG on, so to have TENS, VIS, MAG working

 

3. HB — set realtime display of Heartbeat on both channels

Channel 1 set to HB (Heartbeat)

Channel 2 setting (to show the Heartbeat as on Ch1)

4. Erasing and Recording the memory 

If you do not use the internal Frequency generator or stored programs you need to upload frequency files to the 2 channels – alternatively you can also record your heartbeat on one or both  channels. To make the BEaMEr ready to record you have to go through the below sequence which deletes all pre-existing frequency data. You can upload Frequencies generated with CoRe program, the Virtual Doctor or files that are generated with other programs, as well as Music or spoken word. Just plugin in your HDMI to audio cable into your headphone output right at the start and at point 6 the  recording will start

Press both buttons at the same time for about 8 sec while the BEaMEr goes through the following steps

(the 6 steps are steps are indicated with the number in the upper left of the annimation below)

1 — the BEaMEr is switched on and goes through the initialization sequence

2 — Battery charge status is shown (in this exaample only 4 out of 5 green LED are lighted which means 80% charge)

3 — the BEaMEr is powered down – but if you keep pressing both buttons the shut-down is reversed and after

4 — about a 4 sec pause while  keeping to press both buttons

5 — the yellow LED start blinking which means the memory is erased – which takes about 1 minute – NOW YOU CAN RELEASE THE 2 BUTTONS

6 — when the green LED start to light-up in sequence and the BEaMEr is waiting for an audio signal to be recorded – the lower yellow LED show the the volume of the connected signal which should be at least 1-2 LED, if less LED are blinking increase the volume, if all 5 are blinking at the same time reduce the volume. If the signal to be recorded is not already playing you can start it now.

Note : if no audio signal has been connected via the audio-download cable for 30 sec  OR no Heartsensor is connected and attached to a client (and channels are set as above in point 2) the green LED stop lighting up but the next time an audio signal is attached, the BEaMEr will automatically start recording without first going through the above sequence

If the audio-signal is paused longer than 30 sec the BEaMEr automatically stops recording while otherwise the recording continues to its maximum recording time of about 8 min

5. CoRe — Automatic selection of Frequencies via the CoRe algorythm based on the Heartbeat recording

Note : in order for you to be able to set the CoRe function, the heartbeat pattern of the client has to be recorded first as described in point 2 and 3, otherwise this Action is just skipped when pressing the action button

6. Display set Actions

By pressing the upper button shortly while the BEaMEr is on, it goes through  a display of all Functions and selected Actions.

Share.

About Author

2 Comments

  1. ettore della mura on

    i use energetix core system ,biolaeser and spirit navigator.
    How can integrate beamer in my clinical practice?
    thank you

    • The BEaMEr gives you the possibility to treat energetically not only once a week but 168 hours per week. Different than with information therapy which is not necessarily getting stronger with repetition, the effects of Energy depends on frequency and duration. We see effects exponentially greater than with anything that has been done with energetic therapy before.
      2. You can now have patients that live far away and you only send them new frequency files that you create with the CoRe system via e-mail and patients just rent the BEaMEr from you for a certain time.
      3. Having friends and family see your patient wear the BEaMEr and hear about treatment results will promote your practice.
      4. The BEaMEr can give energetic support exactly at the time when the body needs it.
      5. It is simply more effective to feed the body with light, electric and magnetic energy directly than have if first to be converted from food.
      6. Diseases of our times like fatigue, lack of ability to concentrate, nervousness, sleep-disorder, anxiety are often directly linked to a lack of energy which cannot be remedied with a once weekly treatment.
      7. Feedback of Eigenfrequencies that are so successful with the Bio-LaesEr can now be done 24/7 with the BEaMEr

Leave A Reply



Dear Friends and Customers

I am sorry to inform you that I have broken-up business relations with Andrea Gadducci and his company Biot Srl.

After years of paying commissions for software and hardware they have now informed me that they consider both to be their property - which according to their lawyer Guliano Lemme also includes the Inventory of Inergetix products that I had stored at their Rome office and for which I paid rent since it was moved there in June 2018 from Germany.

Until we have decided this matter in court i have to warn you not to buy from Andrea - as these goods might be later declared as stolen and you might loose the money you spend.

However I can offer you to buy directly from me and get a 10% discount to what Andrea quotes you. Please contact me at Worldstouching@gmail.com

Thank you for your support in this DLE

Kiran Schmidt